Introducing the i - Flight Chimera 7" Long Range, Long Distance Drone! A super efficient i - Flight 7inch Long-Range bird that can go where you couldn't go before and can carry bigger batteries to get the flight time to surf the swiss alps if you want! Super stiff frame for ...Introducing the i - Flight Chimera 7" Long Range, Long Distance Drone! A super efficient i - Flight 7inch Long-Range bird that can go where you couldn't go before and can carry bigger batteries to get the flight time to surf the swiss alps if you want! Super stiff frame for minimum resonance and 2806.5 motors for maximum 7inch prop control. Fly big batteries top-mounted, or even bigger batteries bottom-mounted, 6cells recommended or 5cells for slow cruising. But whatever style you fly, a Lipo or Lion pack will just do the job.
Recommended 5S 3.000m - Ah above (slow cruising) or 6S 2.500m - Ah above. GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour; Setup instructions included). Vertical and horizontal TBS Crossfire antenna mounts included to cover you and your antenna dead ends just in case.
Go - Pro universal TPU bottom stand included; fits your original Go - Pro bracket and our TPU Go - Pro protectors (additional). - Flight Products! HIGHLIGHTS: - 6mm rigid arm design for more stiffness - Top- and bottom battery mount option - XING 2806.5 efficient wide stator motors - GPS pre-installed for more safety at distance - Go - Pro TPU bottom stand (Go - Pro protector not included) - 360° TPU protection, DJI cam protection and antenna mounts - DJI FPV Air Unit, buttery-smooth 720p A basic PID- and Filter tuning was applied for a great flight experience! To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps" - Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess! Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode" - GPS Rescue is OFF by default to prevent from unwanted or unexpected drone behaviour. Please check our linked article on "GPS Rescue Mode // Setup" FRAME // :Chimera7 - Wheelbase: 320mm - Main body dimension: 258*199mm - Bottom to top distance: 20mm - Arm thickness: 6mm - Bottom plate thickness: 3mm - Top plate thickness: 2mm - Upper(middle) plate thickness: 3mm - Camera plate thickness: 3mm (included TPU inserts) ELECTRONICS // Succe - X-D F7 V2.1 Stack (50A 4-in-1 ESC): Succe - X-D F7 V2.1 Twin - G: - MCU: 216MHz STM32F722 - Gyro:2x ICM20689 - Baro: YES - Blackbox:32MB - Betaflight OSD: YES - BEC: 5V 2.5A / 9V 2.5A - Current sensor scale: 100 - Inverter for SBUS input (UART2-RX) - Smartaudio & Tramp VTX protocol supported - Beeper pad : Yes - RSSI input pad: No - UARTs:5 - Motor outputs: 8 - 8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5) - 6 pin DJI Air Unit port (R1, GND, R2, T2, GND, 9V) - BLHeli32 Telemetry:RX5 - Input voltage:recommended 2-6S, MAX 8S - Firmware Target: IFLIGHT_F722_TWING - Mounting pattern: 30.5*30.5mm φ4mm with Grommets φ3mm - Dimensions: 36*36mm - Weight: 7.5g - USB type-C ESC // Succe - X 50A: - MCU: STM32F051 - Up tp 48k - Hz PWM frequency - Capacitance: 470u - F/50V - Current Sensor: Yes - Input: 2-6S LIPO - Constant: 50A / Burst: 60A - Bl - Heli32 telemetry: Yes - BEC: No - Supports up to Dshot1200, Proshot, Oneshot, Multishot - Target: i - Flight-BL32-4IN1 - Weight: 14.4g - Mounting pattern: 30.5*30.5mm/Φ3mm - Dimensions: 43*39mm (including the power pads) BNF // Parts list (Build): Prebuilt and indoor tested Quadcopter - 1x Chimera7 frame - 1x Go